Finish Mower PTO Shaft 6 Spline on Each End, Fits Landpride, Kubota, Bush Hog Review

Overview

The Finish Mower PTO Shaft 6 Spline on Each End is a direct replacement driveshaft designed for mid-mount finish mowers from Landpride, Kubota, Bush Hog, and similar brands. It’s built for owners of compact tractors or zero-turn mowers with a 6-spline PTO output, who need a reliable, no-nonsense shaft to keep their mower deck spinning smoothly. At $128.99, it’s a budget-friendly option for replacing a worn or broken shaft without the dealer markup.

Who Should Buy This

• Compact tractor owners with a finish mower deck – If you run a Kubota B or L series, or a Landpride or Bush Hog finish mower, and your current PTO shaft is bent, stripped, or rattling, this is a straightforward swap.
• DIY-minded homeowners – You’re comfortable pulling a cotter pin and sliding a shaft on. No special tools or dealer trips needed.
• Anyone needing a 6-spline, 6-spline configuration – Both ends are identical (6 spline male/female), so it’s ideal for mowers that don’t use a quick-disconnect or shear-pin setup.
• Budget-conscious buyers – At under $130, it’s half the price of many OEM shafts, and with 16 reviews averaging 4.7 stars, it’s proven to work.

Key Features Breakdown

• 6 Spline on Each End – This is a universal fit for most compact tractor PTO outputs and mower gearbox inputs. The splines are cut cleanly and engage without slop, which reduces vibration and wear on the gearbox seal.
• PTO Shaft Length – While the product page doesn’t specify exact collapsed/extended lengths, typical finish mower shafts run 18–24 inches collapsed. Measure your old shaft from yoke center to yoke center to confirm fit. This shaft is designed for standard mid-mount decks, not wide offset or pull-behind finish mowers.
• Material & Build – The shaft is made from heat-treated steel with a telescoping inner tube. It’s not a heavy-duty industrial shaft, but it’s plenty robust for residential and light commercial finish mowing on 1–5 acre lawns.
• Shear Pin or Friction Clutch? – This shaft does not include a shear pin or slip clutch. It relies on the mower’s gearbox or belt system for overload protection. That’s fine for most finish mowers, but if your deck has a shear pin on the input, you’ll need to add one.
• Yoke Fit – The yokes are standard 1-3/8” diameter with a 1/8” keyway and 3/8” locking pin holes. This matches virtually all compact tractor PTO stubs and finish mower gearboxes.

Pros

1. Direct fit for common brands – Owners report it bolts right onto Landpride, Kubota, and Bush Hog decks with zero modification. No filing, grinding, or adapter shopping.
2. Smooth operation – The telescoping section slides easily, so it won’t bind when your mower deck moves up and down. That prevents premature wear on the gearbox input.
3. Solid value – At $128.99, it’s roughly 40% less than a dealer replacement shaft. You’re paying for function, not a brand name.
4. Easy install – Slide the shaft onto the PTO stub, lock with a pin, and slide the other end onto the gearbox. Takes 10 minutes.
5. Good customer feedback – With a 4.7 rating and 16 reviews, buyers consistently praise the fit and durability for residential use.
6. No plastic parts – Unlike some budget shafts with plastic shear hubs, this is all steel. It’ll last years if you keep it greased.

Cons

1. No shear pin or slip clutch – If your mower deck hits a rock or stump, the shaft won’t protect the gearbox. You’ll need to add a shear pin or rely on your tractor’s PTO clutch.
2. Length not specified – The lack of collapsed/extended dimensions means you have to measure your old shaft. If you guess wrong, it’ll either bottom out or not reach.
3. Not for heavy-duty commercial use – This is a light- to medium-duty shaft. If you’re mowing 10+ acres weekly with a 7-foot finish mower, look for a heavier shaft with a slip clutch.
4. Grease fittings are basic – The shaft has standard zerk fittings, but they’re not recessed. They can get knocked off by debris if you mow in rough conditions.

Bottom Line

The Finish Mower PTO Shaft 6 Spline on Each End is a smart, affordable replacement for compact tractor finish mower owners who need a direct swap without the dealer price tag. It fits Landpride, Kubota, and Bush Hog decks reliably, installs in minutes, and has proven itself with real buyers. Just measure your old shaft carefully and plan to add a shear pin if your mower requires one. For residential mowing on 1–5 acres, this shaft will serve you well. I’d recommend it confidently to any DIY owner who wants a no-drama fix.

Frequently Asked Questions

Will this fit my Kubota BX series tractor with a Landpride finish mower?
Yes, most likely. The BX series uses a 6-spline PTO stub, and Landpride finish mowers like the RCR12 series use the same 6-spline input. Measure your old shaft length to be sure, but the spline pattern matches.

Does this shaft come with a shear pin or bolt?
No. The shaft itself does not include a shear pin. You’ll need to check your mower’s gearbox for a shear pin hole (usually on the input shaft) and buy a standard 1/4” or 5/16” shear bolt separately if needed.

How do I know if the shaft is the right length?
Measure your old shaft from the center of the tractor-side yoke pin hole to the center of the mower-side yoke pin hole when the deck is at mid-height. Collapse the new shaft and compare. If the new shaft is too long, you can cut the inner tube with a hacksaw, but it’s better to confirm before buying.